How many units is 5 mg of MOTS-c?

It depends entirely on how much water you added. In a 10 mg vial reconstituted with 2 mL, the concentration is 5 mg/mL, so 5 mg is 1 mL, which is 100 units on a U-100 insulin syringe. In the same vial with 1 mL of water it is 50 units, and with 3 mL it is 150 units.

How much bacteriostatic water for a 10 mg MOTS-c vial?

2 mL is the usual choice. It gives 5 mg/mL, which puts the commonly reported range of 2.5 mg to 10 mg between roughly 50 and 200 units. Aim for a draw between about 10 and 50 units, where the barrel is easiest to read, and add or remove water to get there.

How many doses are in a 10 mg vial?

Divide 10 by your dose. At 5 mg that is 2 doses, which at three times a week is 5 days.

How many units is 5 mg of MOTS-c?

In a 10 mg vial with 2 mL of water, 100 units, a full 1 mL syringe. In a 10 mg vial with 1 mL of water, 50 units.

MOTS-c dosage calculator

MOTS-c is dosed in whole milligrams a few times a week, so the draw is large.

Peptulator, peptulator.com. Research use only, not medical advice.

The Protocol Pack, free

25 printable pages: dosing cards for the twelve most-used compounds at three water volumes, titration planners, a vial log, and five pages on what to do when it has already gone wrong.

Dose to units at the usual vial and water

Dose	U-100 units	Draw	Doses per vial	Vial lasts
2.5 mg	50 units	0.5 mL	4	9 days
5 mg	100 units	1 mL	2	5 days
7.5 mg	150 units	1.5 mL	1	2 days
10 mg	200 units	2 mL	1	2 days

10 mg vial in 2 mL of bacteriostatic water (5 mg/mL), U-100 insulin syringe, three times a week.

About MOTS-c

MOTS-c is a 16 amino acid peptide encoded in mitochondrial DNA, studied for its effects on metabolism and exercise capacity. It is not an approved medicine and is sold for research use.

Reported protocols are unusual for a peptide: whole milligram doses, 5 to 10 mg, two or three times a week, sometimes as a short daily course. A 10 mg vial with 2 mL of water is 5 mg/mL, so 5 mg is 1 mL, a full U-100 syringe. If you are dosing 10 mg from a 10 mg vial, that is the entire vial, and how much water you add only changes how many injections it takes to get it in. The MOTS-c dosage chart page lays all of this out at three water volumes.

The same 10 mg vial at other water volumes

If the draw is awkward to read, change the water, not the dose. The dose stays the same; only the mark moves.

Vial	BAC water	Concentration	Draw	U-100 units	Doses/vial
10 mg	1 mL	10 mg/mL	0.5 mL	50 units	2
10 mg	2 mL	5 mg/mL	1 mL	100 units	2
10 mg	3 mL	3.33 mg/mL	1.5 mL	150 units	2
40 mg	1 mL	40 mg/mL	0.125 mL	12.5 units	8
40 mg	2 mL	20 mg/mL	0.25 mL	25 units	8
40 mg	3 mL	13.33 mg/mL	0.375 mL	37.5 units	8

All rows above assume a 5 mg dose and a standard U-100 insulin syringe, where 100 units = 1 mL.

How long it lasts in the body

Not well characterised in humans. A decay curve is only drawn where a human half-life is documented, so there is none here. Treat any precise figure for MOTS-c elsewhere with caution.

Common questions

How many units is 5 mg of MOTS-c?: It depends entirely on how much water you added. In a 10 mg vial reconstituted with 2 mL, the concentration is 5 mg/mL, so 5 mg is 1 mL, which is 100 units on a U-100 insulin syringe. In the same vial with 1 mL of water it is 50 units, and with 3 mL it is 150 units.
How much bacteriostatic water for a 10 mg MOTS-c vial?: 2 mL is the usual choice. It gives 5 mg/mL, which puts the commonly reported range of 2.5 mg to 10 mg between roughly 50 and 200 units. Aim for a draw between about 10 and 50 units, where the barrel is easiest to read, and add or remove water to get there.
How many doses are in a 10 mg vial?: Divide 10 by your dose. At 5 mg that is 2 doses, which at three times a week is 5 days.
How many units is 5 mg of MOTS-c?: In a 10 mg vial with 2 mL of water, 100 units, a full 1 mL syringe. In a 10 mg vial with 1 mL of water, 50 units.

IndependentThis site does not sell peptides and is not owned by a vendor.

The maths is openThe formula is on every page and in the methodology. The code is one file with an automated test suite, run before each deploy.

How it earnsAffiliate links on one marked page, never inside the calculator.

ReviewedDose ranges and half-lives checked 3 September 2026.

Buying MOTS-c?

The where to buy page lists the vendors this site uses and what to check first. Peptide Bureau keeps the ranked scorecard.

Where to buyWhat to check before you order Vendor scorecardRanked vendors, at Peptide Bureau Build a full protocolThe stack builder at Peptide Bureau, about two minutes

All calculators and charts

Weight management (GLP-1 family)

Retatrutide calculator Vial, water and weekly dose to syringe units
Tirzepatide calculator The 2.5 to 15 mg ladder, converted
Semaglutide calculator The 0.25 to 2.4 mg ladder, converted
Cagrilintide calculator Amylin analogue, 0.3 to 4.5 mg weekly

Growth hormone axis

HGH (somatropin) calculator IU vials to syringe units
Ipamorelin calculator mcg doses, in mL and units
CJC-1295 (no DAC) calculator No-DAC and DAC, mcg to units
CJC-1295 / Ipamorelin blend calculator The 5 mg + 5 mg blend, per component
Sermorelin calculator Nightly mcg doses to units
Tesamorelin calculator 1 to 2 mg daily, in units
Hexarelin calculator mcg doses to units
IGF-1 LR3 calculator Tens of mcg from very small vials
AOD-9604 calculator 300 mcg daily, in units
MOTS-c calculator (this page)

Repair, skin and blends

BPC-157 calculator mcg doses from a 5 or 10 mg vial
TB-500 calculator Loading and maintenance, in units
BPC-157 / TB-500 blend calculator The Wolverine stack, per component
GHK-Cu calculator 50 to 200 mg vials, mg doses
GLOW blend calculator The 70 mg blend, split per component
KLOW blend calculator The 80 mg blend, split per component

Other compounds

PT-141 calculator 0.5 to 2 mg, as needed
Melanotan II calculator mcg loading doses to units
NAD+ calculator 100 to 1,000 mg vials, 25 to 200 mg doses
Thymosin alpha-1 calculator 1.6 mg twice weekly, in units
Epitalon calculator Short courses of 5 to 10 mg
Kisspeptin-10 calculator mcg doses to units
Glutathione calculator Hundreds of mg, or a 200 mg/mL solution

Dosage charts and schedules

Peptide reconstitution chart Concentration for every vial and water combination
Peptide dosing chart Printable unit tables for every compound
Retatrutide titration schedule 2 to 12 mg in units, stage by stage
Tirzepatide titration schedule 2.5 to 15 mg in units, stage by stage
Semaglutide titration schedule 0.25 to 2.4 mg in units, stage by stage
KLOW dosage and frequency chart The 80 mg blend at 2, 3 and 4 mL, both phases
GLOW dosage chart The 70 mg blend, units to each peptide
Wolverine stack dosing chart BPC-157 + TB-500, blend and separate vials
MOTS-c dosage chart 5 and 10 mg vials at three water volumes
Tirzepatide reconstitution chart Every vial size, every water volume, the whole ladder
Retatrutide dosing chart 1 to 12 mg across 10, 20 and 30 mg vials
Printable dosing charts Four one-page charts to save, pin or print

Tools

Peptide calculator The general tool, any compound
Reconstitution calculator How much water to add, and why it matters
mg to units calculator Both directions, any concentration
Bacteriostatic water calculator Pick a volume that lands where you can read it
How to read an insulin syringe U-100 vs U-40, and the 2.5x error
The Protocol Pack Free 25-page printable reference
Where to buy Vendor notes and what to check first
1 mg to units on an insulin syringe The conversion table for every common concentration

Before you use these numbers This is a unit-conversion tool. It turns a vial strength and a water volume into a concentration, a draw volume and a syringe mark. It does not tell you what to take, whether to take it, or whether a compound is safe for you. Most compounds listed are sold for laboratory research and are not approved for human use. Nothing here is medical advice. Dosing decisions belong with a licensed clinician who knows your history. Always check the strength printed on your own vial rather than trusting a preset.